H06 product manual

Package contents

1x H06 Bluetooth® Wireless Headband.

1x Charging cable, 1m (USB / USB-C).


  • Bluetooth® Version: 5.0.
  • Bluetooth® Codes Supported: AAC, SBC.
  • Operating Range: 10m.
  • Playback Time: 18hrs.
  • Charging Time: 2hrs.
  • Battery Type: 360 mAh Lithium Ion Polymer.
  • Omnidirectional Microphone, standard power: 2.0V, Frequency Range 300-5KHz.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.



Visit www.aiaiai.dk/h06 for instructional pairing videos, troubleshooting, and additional Bluetooth® connectivity information.


H06 is covered by a 2 year limited warranty. For more information visit: www.alalal.dk/help/warranty

NB! Do not twist, bend or expand the headband to extreme positions. This may harm the functionality of the electronics.


This equipment has been tested and found to comply with the Limits for a Class B digital device, pursuant to part 15 of the FCC Rules, These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could vold the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. this device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

First-time connection

Power on your H06 by pressing the middle button until the LED light starts flashing. Now your HO6 is ready to pair with your device.

Activate Bluetoothe on your device and wait for AIAIAI TMA-2 (HO6) to show in your list of available Bluetooth® devices.

Now choose to pair with AIAIAI TMA-2 (HO6), and you are ready to use H06 with your device.

General usage and LED indicators

Power on - Press and hold the middle button until the LED appears (1.5 seconds). HO6 is now ON.

Power off - Press and hold the top button for 4 seconds until the LED turns off. HO6 is now OFF.

Searching for device - When searching for a device the LED light will steadily flash white.

Pairing mode - In pairing mode, the LED will rapidly flash white.

Connected to device - The LED will be constant white.

Battery low - The LED will flash red every 10 seconds.

Music control

Play / Pause - Single, short press on the middle button.

Next track - Double press on the middle button.

Previous track - Triple press on the middle button.

Volume up - Single, short press on the top button.

Volume down - Single, short press on the bottom button.

Device control

Answer Incoming call - Single press on the middle button.

End current call - Single press on the middle button.

Reject Incoming call - Press and hold middle button for 15 second.

Activate voice control - Press and hold the middle button for 1.5 seconds.


To charge H06, connect it to the USB-C cable and to either a USB wall plug, or a computer.

The LED is red until H6 is fully charged. When fully charged, the LED turns white.

Please note: the HO6 will charge faster on a wall charger than on a computer. As a safety precaution, the HO6 will not turn on while charging.

Pairing a new device

Begin pairing: To enter pairing mode on HO6, press and hold the top and bottom buttons until the LED starts flashing. The H06 will now show up as AIAIAl TMA-2 (HO6) in the available devices list on your device’s Bluetooth® settings page.

Exit paring: To exit pairing mode, simply power off the HO6.

Resetting paired devices

To remove all previously paired devices on your HO6, press and hold all three buttons at the same time (top, middle and bottom button for 6 seconds).

Can’t find what you’re looking for?